CITY OF LAWRENCE, NEIGHBORHOOD RESOURC Date:__3/22/06_______
SPECS BY LOCATION/TRADE with Costs
Work Write-up/Re-Bid: ___________ Initial: ____________ Case No: _____________ 1
Walk Through Date: ___________
Bid Date: ___________
Construction Specialist:Tony Hoch Phone: 785-832-3113
Project: CRP032206 Address: 429 INDIANA Street Unit: 1
Location: 1 General Requirements
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 1 General Requirements
2.1 GENERAL PROJECT NOTES
Where applicable, owner will choose paint colors, vinyl sheet goods, kitchen cabinet styles and colors, and light fixtures. Allowances for materials will be as follows:
1. Vinyl sheet goods - $ 2.00 per square foot.
2. Carpet goods - $ 2.00 per square foot.
3. Light fixtures - $40.00 per fixture.
General Contractor will be responsible for the moving of all furniture and all appliances. The Contractor will be responsible for
any damage to furniture and the replacement of all furniture to its original location. Cover all furniture for protection of
finish. Also, all carpets will be covered and protected from construction trash.
All construction trash shall be kept cleaned up at all times. All plumbing and electrical work must be done by a licensed
plumber and electrician. All work shall meet or exceed city codes of the City of Lawrence. Permits are required and
inspections are required by the City Inspectors. The General Contractor is responsible for repairs of wall, ceiling, and
floor damage caused by subcontractors.
All equivalent or equal items will have to be approved by Neighborhood Resources Department representative, Contractor,
and applicant together. NO EXCEPTIONS.
Please pay special attention to all parts of the "Specifications by Location and Trade". This document will explain, in more
detail, about workmanship and what is expected for a quality job.
1.00 AL $0.00 $0.00
35.1 VERIFY QUANTITIES/MEASUREMENTS
All measurements (i.e SF of Drywall, or those provided with drawings) are for the contractor's convenience prior to a mandatory
site inspection to verify all dimensions. All quantities (i.e.number of window units) are as stated. No claim for additional
funds due to discrepancies in measurements or quantities shall be honored if not submitted at the time of the initial proposal.
1.00 GR $0.00 $0.00
36.1 BUILDING PERMITS REQUIRED
The contractor is responsible for submitting a copy of this Neighborhood Resources Department prepared work write up, to the
Building Inspeciton Department, applying for, paying for and receiving required permits prior to starting any work.
Contractors are responsible for calling for code required inspections, and closing all permits before payments are made.
1.00 EA $0.00 $0.00
77.1 NEW MATERIALS REQUIRED
All materials used in connection with this work write-up are to be new, of first quality and without defects - unless stated
otherwise or pre-approved by Owner and Construction Specialist.
1.00 GR $0.00 $0.00
90.1 1 YEAR GENERAL WARRANTY
Contractor shall remedy any defect due to faulty material or workmanship and pay for all damage to other work resulting
therefrom, which appear within one year from final payment. Further, contractor shall furnish owner with all manufacturers'
and suppliers' written warranties covering items furnished under this contract prior to release of the final payment.
1.00 DU $0.00 $0.00
Trade: 9 Environmental Rehab
9003.1 LEAD ABATE. STAND. & GUIDELINES
The execution of this work shall comply with all applicable state, federal and local laws, rules, regulations and
guidelines. Some of these standards include: 29 CFR 1926-Construc- tion Industry Standards, 29 CFR 1926.62-Con-
struction Industry Lead Standard, 29 CFR1910. 1200-Hazard Communication, 40 CFR Part261-EPA Regulations, NCLSH-HUD Lead Paint Guidelines for residential structures.
1.00 $0.00 $0.00
9007.1 CLEAN TO CLEARANCE
Prior to final acceptance of the lead hazard reduction work and all rehabilitation work, the property shall be visually
inspected for any remaining paint chips, dust and debris and lead dust wipe samples shall be obtained from floors, windows
sills and window troughs. The contractor shall re-clean all applicable components and surfaces and pay for all additional
clearance dust sampling if any dust sample results exceedd the thresholds of 40 ug/SF for floors, 250 ug/Sf for window sills
and 400 ug/SF for window troughs.
800.00 SF $1.25 $1,000.00
9023.1 CLEARANCE EXAMINATION
Using a trained and certified lead paint inspector, a lead hazard risk assessor, or if approved, a sampling technician, one hour after completion of all lead hazard reduction, renovation and maintenance work, conduct a visual assessment for evidence of remaining paint chips, visible dust debris and residue. Randomly select four (4) floors, two (2) window sills and two (2) window troughs to dust wipe test as per protocol in the HUD Guidelines. Submit the dust samples, plus a blank sample, to an EPA-accredited lead analytical laboratory for determination of lead content. Provide the owner, occupants and this agency with the clearance report and a "Notice of Lead Hazard Reduction" within 15 days of achieving final clearance, in accordance with 23 CFR Part 35.
1.00 EA $500.00 $500.00
Totals for Location: 1 General Requirements: $1,500.00
Location: 2 Exterior
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 5 Demolition & Disposal
715.1 GUT STRUCTURE INTERIOR
Remove all wall framing, floor and wall finishes, windows, doors, trim, equipment, debris and household items from structure
and dispose of in legal landfill. Broom sweep all floors and rake yard areas.
800.00 SF $5.00 $4,000.00
750.1 DEMO OUTBUILDING
Disconnect and cap off all electrical and plumbing services. Demolish outbuilding to below grade and dispose of debris in
code legal dump.Rake yard clean including nails and glass.
100.00 SF $3.00 $300.00
Trade: 6 Concrete & Paving
1033.1 CONCRETE SIDEWALK CITY
Remove old damaged sidewalk. Replace the sidewalk in a manner which will comply with all aspects of the "City of
Lawrence Residential Sidewalk Requirements" adopted by the City Commission, July 10th, 1996. Remove all forms, regrade
and spot seed.
Finish last 7' on south end of brick walk way.
21.00 SF $15.00 $315.00
1034.1 CONCRETE SIDEWALK HOMEOWNER
Form and pour 4" thick, 2200 psi concrete slab including all form work, 6 mil vapor barrier, 4" gravel base, 10x10 wire mesh
and a steel trowel finish. Remove all forms, regrade and spot seed.
INCLUDE YARD STEPS
120.00 SF $6.00 $720.00
1050.1 CONCRETE RETAINING WALL
Excavate side of hill to allow space to arrange formwork. Place 8"x16" cont. strip ftg. below frost line w/2-#2 rebars 2.5" min.
from edges. Build forms for walls, min 8" thick, w/a batter 7 deg. toward hill from horiz. Place #4 rebar 48" o.c. vert. &
horiz. & tie into ftg @ keyway. Pour & vibrate 2,500 psi conc. min. 3000 psi rec. Allow weep holes @48" o.c. @ lowest grade.
Strip forms & backfill w/pea gravel. Restore topsoil & seed.
51.00 SF $21.00 $1,071.00
855.1 DEMO CONCRETE
Break up concrete and remove off site to code legal dump.
80.00 SF $2.50 $200.00
865.1 FOOTING--PIER
Excavate a square, straight sided hole below the frost line to solid bearing. Pour a 24" x24"x18"pier footing with two #5
reinforcing rods. Cast a rod to anchor pier.
FOR BEAM SUPPORTS ON REAR ROOMS
4.00 EA $165.00 $660.00
870.1 FOOTING--CONTINUOUS
Excavate a square, straightened, trench below frost line to solid bearing. Form and pour a 2500 psi, 18"x9" deep footing
reinforced with at least two #4 rebar securly wired and set on chairs. Remove forms after concrete has fully cured.
JACK AND SUPPORT HOUSE UNDER BLOCK FOUDATION. REMOVE BLOCK FOUNDATION.
86.00 LF $40.00 $3,440.00
Trade: 7 Masonry
1105.1 FOUNDATON--PARGET
Parget foundation wall with 3/8" coat of waterproof cement. Match existing finish as closely as possible.
200.00 SF $1.10 $220.00
1110.1 BLOCK FOUNDATION WALL
Construct an 8"x 16"x 8" thick, reinforced cement block wall with trowel cut joints, 1/2" exterior waterproof pargeting, and a
solid cap block.
588.00 SF $7.00 $4,116.00
Trade: 8 Metal Work
1460.1 METAL GUARD RAIL--WROUGHT
Design, fabricate, prime, topcoat and install a one-piece steel railing of 2" flat top and bottom rails and 1/4" balustrades 6" on
center.
FOR BASEMENT STAIR ENTRANCE.
14.00 LF $56.00 $784.00
Trade: 10 Carpentry
2600.1 SIDING--T1-11
Remove existing siding, Install rough sawn fir, 1/2" thick, factory stained, T1-11 siding sheets, 1"x 3" trim at corners. Use
lap flashing on horizontal seams. Flash or install silicone caulking along entire top edge, and under windows or other
openings.
1,200.00 SF $5.00 $6,000.00
2980.1 WINDOW--VINYL - DBL GLZ
Field measure, order and install a like functioning vinyl, double glazed, replacement window and jamb including screen, caulk,
interior casing and exterior trim. If applicable, provide snap-in or internal grill to match mullion pattern of other openings.
2.00 EA $600.00 $1,200.00
3560.1 PORCH--REBUILD
Remove deteriorated porch. Construct 12"x 12" masonry piers, 2"x 10" joists with 3/4" tongue and groove flooring to support
child-proof wood railing and 4"x 4" posts for roof. Construct roof structure with 2"x 6" rafters, 1/2" plywood deck, fiberglass
shingles, aluminum gutter and downspouts and 1/4" plywood ceiling. Structural lumber and deck shall be preservative
treated.
140.00 SF $26.00 $3,640.00
3590.1 STEPS/LANDING--REPL EXTERIOR
Dispose of existing steps and landing. Construct a replacement unit with two 2"x 12" preservative treated pine stringers,
5/4" PTP stepping stock treads, on a solid concrete footer. Frame stairs 3' wide connecting to porch. Construct a wood
handrail on one side 32" above tread nosing.
1.00 EA $280.00 $280.00
Trade: 15 Roofing
4490.1 ROOF SHEATHING 1/2"
Remove Sheathing and Install 1/2" CDX plywood sheathing nailed 8" on center using plywood clips.
1,000.00 SF $2.10 $2,100.00
4525.1 ROOF--90 LB. ROLL
Install 90 lb. mineralized fiberglass roll roofing using a 4" minimum overlap, nailed 6" on center with asphalt roofing cement
per manufacturer's specs. Replace all flashing with .019 aluminum.
4.50 SQ $225.00 $1,012.50
4580.1 TEAR OFF AND REROOF SHINGLES
Remove and dispose of all roofing & defective sheathing. Cut a 1" wide vent at ridge board. Allow for replacement of up to 5 sf
of sheathing per 100 sf of roof using pine board or CDX plywood of matching thickness. Install 15 lb felt. Install preformed and
prefinished drip edge, and vent pipe boots. Install a 220 lb fiberglass asphalt, 3 tab shingle with a 25 yr warranty. Replace all
flashing. Install shingle-over ridge vent.
7.00 SQ $225.00 $1,575.00
4635.1 GUTTER--5" SEAMLESS ALUMINUM
Dispose of gutter. Install 5", K- type, seamless, .027 gauge aluminum gutter to service roof. White or color choice by owner.
80.00 LF $5.00 $400.00
4640.1 DOWNSPOUT--5" SEAMLESS ALUMINUM
Dispose of downspout. Install 5", square, seamless, .027 gauge, aluminum downspout. Strap at least 3' on center. White or
color choice by owner.
AT 4 LOCATIONS
50.00 LF $4.00 $200.00
4665.1 SPLASH BLOCK
Place concrete or plastic splash block at end of downspout.
4.00 EA $20.00 $80.00
4755.1 FASCIA 1"X 6"
Install a 1"x 6", #2 pine fascia with bevel cut joints using galvanized finish nails. Caulk over joints, and prime.
150.00 LF $4.60 $690.00
4760.1 SOFFIT
Install 1/4" BCX plywood soffit.
110.00 SF $3.10 $341.00
Trade: 19 Paint & Wallpaper
5656.1 PREP & PAINT EXTERIOR WOOD
Cover ground with drop cloth. Scrape all loose, cracked, peeling and blistered paint. Remove all deteriorated glazing compound. Feather edges and dull gloss with sandpaper. Dispose of chips properly. Mask or remove exterior fixtures. Clean all surfaces to paint manufacturer's requirements. Caulk and fill holes. Reglaze sash where compound is missing. Spot prime and top coat with two coats of two colors with owner's choice of premixed acrylic latex. If an airless sprayer is used, the first coat must be brushed or rolled into the surface to promote good adhesion. Where gutters and downspouts are to remain, painting of these should be included. Removal and replacement of storm windows should be included. Painting of wood shutters should be included.
1.00 DU $4,500.00 $4,500.00
Totals for Location: 2 Exterior: $37,844.50
Location: 3 Basement
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 7 Masonry
1105.1 FOUNDATON--PARGET
Parget foundation wall with 3/8" coat of waterproof cement. Match existing finish as closely as possible.
INTERIOR OF STONE WALLS.
420.00 SF $1.10 $462.00
Trade: 21 HVAC
6050.1 FURNACE & DUCT--GAS: 80,000 BTU
Install an 80,000 BTU, intermit. pilot, forced air furnace, minimum AFUE rating of 80; complete with plenum, insulated
supply duct, galvanized return duct connected to wall registers, to service all rooms. Include setback thermostat, filter,
fan and plenum control. (Connect thimble breaching to chimney per code. Provide separate power circuit per code. "As
needed") Provide operating manual to owner.
1.00 EA $4,210.00 $4,210.00
6410.1 FLUE REPLACE
Install a prefabricated, double walled, UL listed, galvanized steel, 8" flue inside chimney.
20.00 LF $45.00 $900.00
Trade: 22 Plumbing
6612.1 WATER SERVICE--COPPER K LINE
Excavate to 36", lay 1" type K, copper pipe and refill trench for water service. Lay line without joints from meter hub to main
shut off valve inside structure. Contractor to apply and pay for all permits, repair concrete cuts and coordinate installation
of new meter. Owner to pay all water tap fees. Backfill, seed and mulch disturbed yard areas.
40.00 LF $52.00 $2,080.00
6765.1 GAS LINE
Hang 3/4" main and 1/2" fixture gas supply lines of schedule 40 black steel pipe with malleable iron screwed fittings. Install
brass stop valves at all equipment.
60.00 LF $14.65 $879.00
7070.1 WATER HEATER--40 GALLON GAS
Install a 40 gallon, glass lined, high recovery, insulated to minimum R-7, gas water heater with a 6 year warranty. Include
pressure and temperature relief valve, discharge tube to within 6" of floor or to outside of structure, vent, thimble, and gas
piping from shut-off valve to fixture. Dispose of old water heater in code legal dump.
1.00 EA $500.00 $500.00
7190.1 WATER SUPPLY--1 BATH HOUSE
Remove all water supply from meter on, to code legal dump. Install type M copper supply lines with 3/4" main, 1/2" fixture
grouping trunk, and 3/8" individual supply lines to service one 3-piece bath, kitchen & laundry area. Installation shall be
complete, code compliant, fully usable, and include shut-off valves, chromed fixture supply lines & air gaps.
1.00 EA $2,700.00 $2,700.00
7210.1 DRAIN/WASTE/VENT--1 BATH HSE
Remove all drain, waste and wet vent lines to code legal dump. Install schedule 40 PVC or cast iron DWV lines to service
one 3-piece bath, kitchen and laundry area from the foundation perimeter to roof vent terminus.
1.00 DU $2,100.00 $2,100.00
Trade: 23 Electric
7470.1 ELECTRIC SERVICE--150 AMP
Dispose of old electric service to code legal dump. Install a residential, 150 amp, single phase, 3 wire electric service.
Include a main disconnect, 30 circuit panel board, meter socket, weather head, service cable, and ground rod and cable.
Caulk exterior service penetration.
1.00 EA $1,250.00 $1,250.00
8105.1 WIRING SYSTEM REPAIR
Inspect, test and repair existing wiring system throughout the structure. Install all necessary materials so that each existing
outlet, fixture, motor, switch and circuit will operate properly and will conform to local electrical code. Verify that fixtures are
securely mounted to wall or ceiling; which may require the installation of ceiling-fan rated boxes. Dispose of all defective and
unnecessary wiring. Fish all wire and patch all tear out.
1.00 DU $2,500.00 $2,500.00
Totals for Location: 3 Basement: $17,581.00
Location: 4 Kitchen/dining
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 10 Carpentry
2840.1 TRIM--WINDOW SET, INTERIOR
Trim window including header, stops, casings, stool and apron in 2-1/2" wide finger jointed pine.
2.00 EA $57.00 $114.00
3310.1 TRIM--DOOR SET FINGER JOINTED
Trim both sides of interior door, including header, stops, and casings. Use 2-1/2" wide clamshell, finger jointed pine.
1.00 EA $60.00 $60.00
3345.1 DOOR--FLUSH INT, HOLLOW CORE
Install flush, hollow core door on existing jamb to match. Include privacy lockset and hinges.
1.00 EA $112.00 $112.00
3715.1 CABINET--WOOD BASE
Dispose of base cabinets. Install base cabinet with doors of solid birch or ash stiles and veneered plywood panels. Frame
with solid birch or ash stiles, 1/4" veneered plywood sides and metal or plastic corner bracing. Drawers shall be made of
wood or composition material. Owner's choice of two in-stock designs.
12.00 LF $106.00 $1,272.00
3725.1 CABINET--WOOD WALL
Dispose of wall cabinets. Field measure and screw to studs, level and plumb, kitchen wall cabinet. Door to have solid wood
stiles and plywood panels. Frame to have solid wood stiles, 1/4" plywood sides, metal or plastic corner bracing.
12.00 LF $70.00 $840.00
3750.1 COUNTER TOP--PLASTIC LAMINATE
Dispose of counter top. Field measure and screw to base cabinet a post formed, plastic laminate counter top. Provide cutout
for sink. Owner's choice of in-stock color and texture.
12.00 LF $35.00 $420.00
Trade: 17 Drywall & Plaster
5265.1 DRYWALL--3/8"
Hang, tape and 3 coat finish 3/8" drywall. Glue each framing member and screw or nail 8" on center. Run boards with long
dimension horizontal. Sand ready for paint.
1,204.00 SF $1.00 $1,204.00
Trade: 19 Paint & Wallpaper
5555.1 PREP/PAINT KITCHEN--SEMI GLOSS
Remove/cover all hardware, fixtures not to be painted. Wet scrape loose, cracked, peeling, blistered surfaces. Feather edges
& dull gloss surfaces w/sandpaper. Clean all surfaces with TSP. Fill all holes/cracks. Spot prime with acrylic latex. Apply
top coat of owner's choice of premixed acrylic latex semi-gloss. Include any closets.
1.00 RM $500.00 $500.00
Trade: 20 Floor Coverings
5930.1 UNDERLAY & VINYL SHEET GOODS
Install 5/16" underlayment grade plywood, using 7d screw shank or cement coated nails, 6" on center allowing a 1/4" gap at
wall. Install 070" thick, backed vinyl sheet goods w/ minimum seams, per manufact. recommendations. Caulk edges of vinyl
w/clear silicone caulk to create positive seal. Install metal edge strips in openings & shoe molding or 4" vinyl base around
perimeter.
350.00 SF $6.00 $2,100.00
Trade: 22 Plumbing
6835.1 SINK--DOUBLE BOWL COMPLETE
Install a 33"x22"x5" double bowl, stainless steel, self rimming kitchen sink including a single control, metal bodied faucet
with a "limited lifetime function and finish warranty" American Standard or equal and maximum flow of 2 gallons per minute,
trap, supply lines, and shut-off valves.
1.00 EA $500.00 $500.00
Trade: 23 Electric
7730.1 LIGHT FIXTURE--REPLACE
Replace a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and lamps. $20 allowance for fixture.
2.00 EA $40.00 $80.00
Totals for Location: 4 Kitchen/dining: $7,202.00
Location: 5 Bathroom
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 10 Carpentry
2840.1 TRIM--WINDOW SET, INTERIOR
Trim window including header, stops, casings, stool and apron in 2-1/2" wide finger jointed pine.
1.00 EA $57.00 $57.00
3360.1 DOOR--PREHUNG PASSAGE
Install a 1-3/8" prehung, flush, luaun door and split jamb including casing both sides, 2 butt hinges and a privacy lockset.
1.00 EA $160.00 $160.00
3680.1 TUB SURROUND--PREFAB
Install a white fiberglass or acrylic, 3- or 5-piece, tub surround kit with a built-in soap dish. Caulk all joints with white,
mildew resistant siliconized caulk. Prepare substrate and attach panels using manufacturer's recommended adhesive and
fasteners.
1.00 EA $265.00 $265.00
3835.1 ACCESSORY SET--6 PIECE CHROME
Install a chrome plated steel bathroom accessory set consisting of two 24" towel bars, soap dish, tumbler holder, soap and
grab, and toilet paper holder. $55 allowance per set.
1.00 EA $115.00 $115.00
3840.1 SHOWER CURTAIN ROD
Dispose of shower curtain rod. Fill all holes or irregularities, flush with surrounding finish. Install a chrome shower curtain
rod using wall anchors.
1.00 EA $25.00 $25.00
Trade: 17 Drywall & Plaster
5265.1 DRYWALL--3/8"
Hang, tape and 3 coat finish 3/8" drywall. Glue each framing member and screw or nail 8" on center. Run boards with long
dimension horizontal. Sand ready for paint.
320.00 SF $1.00 $320.00
Trade: 19 Paint & Wallpaper
5560.1 PREP & PAINT BATHROOM
Remove/cover all hardware and fixtures not to be painted. Wet scrape all loose cracked, peeling blistered surfaces. Clean
surfaces with TSP. Fill all holes and cracks. Spot prime with acrylic latex. Apply top coat of owner's choice of premixed
acrylic latex semi-gloss.
1.00 RM $200.00 $200.00
Trade: 20 Floor Coverings
5930.1 UNDERLAY & VINYL SHEET GOODS
Install 5/16" underlayment grade plywood, using 7d screw shank or cement coated nails, 6" on center allowing a 1/4" gap at
wall. Install 070" thick, backed vinyl sheet goods w/ minimum seams, per manufact. recommendations. Caulk edges of vinyl
w/clear silicone caulk to create positive seal. Install metal edge strips in openings & shoe molding or 4" vinyl base around
perimeter.
70.00 SF $6.00 $420.00
Trade: 22 Plumbing
6900.1 VANITY--24" COMPLETE
Install a 24" vanity complete with plywood cabinet, cultured marble top, dual control, brass bodied, single lever faucet, supply
risers, shut-off valves and all required waste connectors to complete the installation.
1.00 EA $565.00 $565.00
6945.1 BATHTUB--5' STEEL COMPLETE
Install a 5' white, enameled, formed steel, tub complete with lever operated pop up drain and overflow, PVC waste, single
lever, metal faucet, shower diverter and Delta 6122 water saving shower head.
1.00 EA $835.00 $835.00
7010.1 COMMODE--REPLACE
Install 2 piece, close coupled, white, vitreous china, water saving commode made by American Standard, or equal. Include
plastic or pressed wood white seat, supply pipe, shut-off valve, flap valve and wax seal. Allow for floor flange
replacement if necessary. Use 14" rough-in when replacing wall hung commode, and 12" rough-in to replace close
coupled commode.
1.00 EA $275.00 $275.00
Trade: 23 Electric
7816.1 FIXTURE--HEAT, LIGHT, VENT
Install a ceiling mounted fixture containing a 1200 watt, forced air heater, a single bulb light fixture, and an exterior
ducted vent fan with damper capable of 60 cfm, controlled by 3 manufacturer-supplied switches on an independent 20 amp
circuit, using #14 copper Romex. Fish all wireand patch all tear out.
1.00 EA $325.00 $325.00
Totals for Location: 5 Bathroom: $3,562.00
Location: 6 Living Room
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 10 Carpentry
2840.1 TRIM--WINDOW SET, INTERIOR
Trim window including header, stops, casings, stool and apron in 2-1/2" wide finger jointed pine.
4.00 EA $57.00 $228.00
3310.1 TRIM--DOOR SET FINGER JOINTED
Trim both sides of interior door, including header, stops, and casings. Use 2-1/2" wide clamshell, finger jointed pine.
1.00 EA $60.00 $60.00
3360.1 DOOR--PREHUNG PASSAGE
Install a 1-3/8" prehung, flush, luaun door and split jamb including casing both sides, 2 butt hinges and a privacy lockset.
1.00 EA $160.00 $160.00
Trade: 17 Drywall & Plaster
5265.1 DRYWALL--3/8"
Hang, tape and 3 coat finish 3/8" drywall. Glue each framing member and screw or nail 8" on center. Run boards with long
dimension horizontal. Sand ready for paint.
860.00 SF $1.00 $860.00
Trade: 19 Paint & Wallpaper
5565.1 PREP & PAINT VACANT ROOM
Remove/cover all hardware, fixtures not to be painted. Wet scrape loose, cracked, peeling, blistered surfaces. Feather edges
& dull gloss surfaces with sandpaper. Clean all surfaces with TSP. Spot prime and top coat trim, ceiling, walls, doors &
windows with owner's choice of premixed acrylic latex. Include any closets.
1.00 RM $300.00 $300.00
Trade: 20 Floor Coverings
5970.1 CARPET AND PAD
Install FHA approved, nylon, plush carpet over a 1/2" medium density rebond pad w/ a minimum of seams. Stretch carpet to
eliminate puckers, scallops & ripples. Include tackless strips, metal edge strips, and mending tape to cover entire floor
including closets. On stairs, fasten carpet and pad at top and bottom of each riser. Owner's choice of stock color and
pattern.
35.00 SY $26.00 $910.00
Trade: 23 Electric
7730.1 LIGHT FIXTURE--REPLACE
Replace a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and lamps. $20 allowance for fixture.
2.00 EA $40.00 $80.00
Totals for Location: 6 Living Room: $2,598.00
Location: 7 Rear Porch
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 10 Carpentry
3560.1 PORCH--REBUILD
Remove deteriorated porch. Construct 12"x 12" masonry piers, 2"x 10" joists with 3/4" tongue and groove flooring to support
child-proof wood railing and 4"x 4" posts for roof. Construct roof structure with 2"x 6" rafters, 1/2" plywood deck, fiberglass
shingles, aluminum gutter and downspouts and 1/4" plywood ceiling. Structural lumber and deck shall be preservative
treated.
72.00 SF $26.00 $1,872.00
3590.1 STEPS/LANDING--REPL EXTERIOR
Dispose of existing steps and landing. Construct a replacement unit with two 2"x 12" preservative treated pine stringers, 5/4"
PTP stepping stock treads, on a solid concrete footer. Frame stairs 3' wide connecting to a 5'x 6' landing, of 2"x 6"s and
2"x 4" deck. Construct a wood handrail on one side 32" above tread nosing.
1.00 EA $480.00 $480.00
Totals for Location: 7 Rear Porch: $2,352.00
Location: 8 Utility Room
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 10 Carpentry
2840.1 TRIM--WINDOW SET, INTERIOR
Trim window including header, stops, casings, stool and apron in 2-1/2" wide finger jointed pine.
2.00 EA $57.00 $114.00
3310.1 TRIM--DOOR SET FINGER JOINTED
Trim both sides of interior door, including header, stops, and casings. Use 2-1/2" wide clamshell, finger jointed pine.
1.00 EA $60.00 $60.00
Trade: 17 Drywall & Plaster
5265.1 DRYWALL--3/8"
Hang, tape and 3 coat finish 3/8" drywall. Glue each framing member and screw or nail 8" on center. Run boards with long
dimension horizontal. Sand ready for paint.
388.00 SF $1.00 $388.00
Trade: 19 Paint & Wallpaper
5565.1 PREP & PAINT VACANT ROOM
Remove/cover all hardware, fixtures not to be painted. Wet scrape loose, cracked, peeling, blistered surfaces. Feather edges
& dull gloss surfaces with sandpaper. Clean all surfaces with TSP. Spot prime and top coat trim, ceiling, walls, doors &
windows with owner's choice of premixed acrylic latex. Include any closets.
1.00 RM $300.00 $300.00
Trade: 20 Floor Coverings
5930.1 UNDERLAY & VINYL SHEET GOODS
Install 5/16" underlayment grade plywood, using 7d screw shank or cement coated nails, 6" on center allowing a 1/4" gap at
wall. Install 070" thick, backed vinyl sheet goods w/ minimum seams, per manufact. recommendations. Caulk edges of vinyl
w/clear silicone caulk to create positive seal. Install metal edge strips in openings & shoe molding or 4" vinyl base around
perimeter.
96.00 SF $6.00 $576.00
Trade: 23 Electric
7730.1 LIGHT FIXTURE--REPLACE
Replace a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and lamps. $20 allowance for fixture.
1.00 EA $40.00 $40.00
Totals for Location: 8 Utility Room: $1,478.00
Location: 9 Bedroom
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 10 Carpentry
2980.1 WINDOW--VINYL - DBL GLZ
Field measure, order and install a like functioning vinyl, double glazed, replacement window and jamb including screen, caulk,
interior casing and exterior trim. If applicable, provide snap-in or internal grill to match mullion pattern of other openings.
Include framed opening.
2.00 EA $750.00 $1,500.00
3360.1 DOOR--PREHUNG PASSAGE
Install a 1-3/8" prehung, flush, luaun door and split jamb including casing both sides, 2 butt hinges and a privacy lockset.
1.00 EA $160.00 $160.00
Trade: 17 Drywall & Plaster
5265.1 DRYWALL--3/8"
Hang, tape and 3 coat finish 3/8" drywall. Glue each framing member and screw or nail 8" on center. Run boards with long
dimension horizontal. Sand ready for paint.
420.00 SF $1.00 $420.00
Trade: 19 Paint & Wallpaper
5565.1 PREP & PAINT VACANT ROOM
Remove/cover all hardware, fixtures not to be painted. Wet scrape loose, cracked, peeling, blistered surfaces. Feather edges
& dull gloss surfaces with sandpaper. Clean all surfaces with TSP. Spot prime and top coat trim, ceiling, walls, doors &
windows with owner's choice of premixed acrylic latex. Include any closets.
1.00 RM $300.00 $300.00
Trade: 20 Floor Coverings
5970.1 CARPET AND PAD
Install FHA approved, nylon, plush carpet over a 1/2" medium density rebond pad w/ a minimum of seams. Stretch carpet to
eliminate puckers, scallops & ripples. Include tackless strips, metal edge strips, and mending tape to cover entire floor
including closets. On stairs, fasten carpet and pad at top and bottom of each riser. Owner's choice of stock color and
pattern.
12.00 SY $26.00 $312.00
Trade: 23 Electric
7730.1 LIGHT FIXTURE--REPLACE
Replace a ceiling mounted, 2 bulb, UL approved, incandescent light fixture with shade and lamps. $20 allowance for fixture.
1.00 EA $40.00 $40.00
Totals for Location: 9 Bedroom: $2,732.00
Location: 10 Attic
Spec Unit Total
Number Spec Quantity Units Price Price
Trade: 15 Roofing
4425.1 RAFTER--2"X 8" REPLACE
Dispose of existing defective rafter. Install a 2"x 8" pine rafter, crown up, from ridge board to fascia. Renail sheathing with
coated sinkers to new rafter.
600.00 LF $1.60 $960.00
4450.1 FRAME ROOF--FLAT 2"X 8"
Frame roof structure for flat roof using 2"x8" pine, 16" on center and 1/2" CDX sheathing.
232.00 SF $4.10 $951.20
Trade: 16 Conservation
4905.1 INSULATE WALL--R-13 BATT
Staple 3-1/2" thick, R-13, foil faced fiberglass roll insulation to studs per manufacturer's specifications.
1,100.00 SF $0.55 $605.00
4935.1 ATTIC R-30 CELLULOSE
Blow in borax treated, cellulose insulation per manufacturer's specifications to create an R-30 rating. Cover any recessed
ceiling light fixtures with an approved baffle. Replace all material removed or cut to gain access to match existing materials.
800.00 SF $1.25 $1,000.00
Totals for Location: 10 Attic: $3,516.20
Total for project CRP032206 / 429 INDIANA Street / 1: $80,365.70